MS41 Live
ENFR
Request beta access
Documentation — Wiring

MS41 Live / Docs / Wiring

Wiring

MS41 Live reads three analog inputs that already exist on the ECU connector. Nothing is added inside the ECU. All three are 0–5 V only.

The three analog inputs

ECU pinStock functionDefault use in MS41 Live
75Lambda 1 signal (pre-cat sensor, bank 1)Wideband analog output
76Lambda 2 signal (pre-cat sensor, bank 2)MAP sensor signal
8MAF sensor signalClutch switch (optional, VE mode with the MAF unplugged)

Each function can be moved to another of these pins on the Inputs & sensors page of the editor, which warns when two functions are set to the same pin. Re-assigning inputs has not been validated on a car yet: the default assignment above is the one that has been driven.

Supply and ground for the sensors come from the throttle-position-sensor feed:

ECU pinFunctionUsed for
44+5 V sensor supply (throttle position sensor)MAP sensor supply
42Sensor ground (throttle position sensor)MAP sensor ground, divider ground

Pin numbers are those of the 88-pin MS41 connector as given by commonly available pin-out tables. Check them against the wiring diagram of your car, and confirm each wire with a multimeter before you connect anything.

Default sensor wiring The wideband controller's analog output goes to the Lambda 1 input, pin 75, with its analog ground on the Lambda 1 sensor ground. The MAP sensor signal goes to the Lambda 2 input, pin 76, with 5 volts from pin 44 and ground from pin 42, the throttle-position-sensor feed. An optional clutch switch goes to the MAF signal input, pin 8, through a resistor divider if its line carries 12 volts. 0–5 V ANALOG 0–5 V divider if the line carries 12 V Wideband controllerwith its own sensor in the exhaust analog out +analog out − MAP sensor3 bar typical signal+5 Vground Clutch switchoptional switch line MS41 ECU88-pin connector 75Lambda 1 input GNDLambda 1 sensor ground 76Lambda 2 input 44+5 V sensor supply 42sensor ground THROTTLE-POSITION-SENSOR FEED 8MAF signal input
Default assignment. Orange: 0–5 V signals. Grey: supply and grounds.

Where to connect

You do not have to go into the ECU connector. The signal wires of the two pre-cat oxygen sensor plugs run to pins 75 and 76, and the throttle position sensor plug carries the 5 V supply and the sensor ground. Splice there, solder and insulate properly, and keep the analog wires away from ignition leads and coils.

MAP sensor

With the engine off, the MAP gauge must read barometric pressure. Calibration: Sensors & calibration.

Wideband controller

On the development car the bank 1 plug had four wires — signal, sensor ground, switched 12 V for the heater, heater control — and the controller is fed from that switched 12 V through a 5 A fuse. Wire colours vary: identify each wire by measurement.

What to expect. With the stock sensors removed, the ECU stores oxygen-sensor heater faults. In wideband mode they do not prevent closed loop. In wideband mode the ECU runs a single lambda channel: both banks receive the same correction, measured where your wideband sensor sits.

Clutch switch (optional)

The clutch input is an analog input with a threshold: below the threshold the pedal is “released”, above it “pressed”. The threshold is set in volts on the Motorsport › Clutch page.

By default the clutch switch uses the MAF signal input (pin 8). That is only possible in VE mode with the MAF sensor unplugged: a connected MAF drives that pin itself. The development car runs this way.

If the switch line can carry 12 V

Many pedal switches are fed by another control unit, so the wire carries about 12 V in one position. Bring it into range with a two-resistor divider:

On the development car: 8.1 kΩ from the line to the input and 5.4 kΩ from the input to ground (built from 2.7 kΩ resistors). The MAF input itself loads the divider — about 2.5 kΩ to ground, measured — so the voltage at the pin is lower than the divider alone would give: 0.1 V released, about 1.8 V pressed with the engine running. The threshold is set to 1.0 V.

If the switch only connects to ground

A switch that is either open or grounded needs a pull-up resistor to the 5 V sensor supply so that the input sees a voltage when the switch is open. Choose it so that the “open” voltage sits well above your threshold, taking the input’s own load into account. This variant has not been built on the development car.

In both cases: measure the two voltages at the ECU pin with a multimeter, set the threshold halfway, and check that the Clutch gauge in the editor switches between 0 and 1 with the pedal.

Warnings

  • Never apply more than 5 V to pins 75, 76 or 8. No 12 V signal directly on an analog input.
  • Never connect a pull-up to the 5 V sensor supply on a wire that can carry 12 V: the 12 V would feed back into the supply of the throttle position sensor and the MAP sensor. Measure the wire with the ignition on first.
  • Use the sensor ground for analog grounds, not the chassis.
  • Do not overload the 5 V sensor supply: it is meant for sensors, not for powering a controller or a gauge.
  • Disconnect the battery while you work on the harness, and recheck every connection before the first start.