Documentation — Motorsport functions
MS41 Live / Docs / Motorsport functions
Motorsport functions
Launch control, flat shift, a hard-cut rev limiter and two protections. They are off in the base tunes. Settings that carry the LIVE badge in the editor can be changed with the engine running.
For off-road and motorsport use. These functions cut fuel on purpose and hold the engine at high load: use them on a healthy engine, with a tune whose mixture you have checked.
The clutch signal
Motorsport › Clutch chooses where the “clutch pressed” information comes from:
- Pedal switch — a switch wired to an analog input, with a threshold in volts. Wiring: Wiring.
- RPM-rise detection — no switch: flat shift recognises the shift from how fast the engine speed rises when the clutch is released under full throttle.
The Clutch gauge shows the state the ECU sees.
Launch control
With the car stationary and the throttle down, launch control holds the engine at a set speed with a fixed ignition angle, until the car moves.
| Setting | Base tune | What it does |
|---|---|---|
| Enable | off | Switches launch control on. |
| RPM | 3008 rpm | Engine speed held during the launch. |
| Timing | 0.0° | Fixed ignition angle while launch control is limiting. |
| Max speed | 5 km/h | Launch control only acts below this vehicle speed. |
| Min throttle | 80 % | Launch control only acts above this throttle opening. |
| Clutch required | off | When on, launch control also needs the clutch pedal switch to be pressed. |
On the development car, a 3008 rpm setting held the engine between roughly 2900 and 3250 rpm.
The ECU’s vehicle-speed value is refreshed about once per second. Without “Clutch required”, launch control can therefore stay active for a moment after the car has started to move. With a pedal switch and “Clutch required” on, it ends when you release the pedal.
Flat shift
Flat shift lets you keep the throttle floored during an upshift: while the clutch is down, the ECU holds the engine speed where it was with a hard cut and a fixed ignition angle, then releases it when the shift is done.
| Setting | Base tune | What it does |
|---|---|---|
| Enable | off | Switches flat shift on. |
| Min RPM | 3000 rpm | No flat shift below this engine speed. |
| Timing | 0.0° | Fixed ignition angle while flat shift is limiting. |
| Min speed | 20 km/h | No flat shift below this vehicle speed. |
| Min throttle | 80 % | The throttle opening that counts as “floored”. |
| Full-throttle time before arming | 500 ms | The throttle must have been held above “Min throttle”, without interruption, for this long before a shift is accepted. |
| Detection threshold | 5000 rpm/s | Clutch-less mode only: the RPM rise rate that is taken as “clutch released”. |
| Max duration | 1500 ms | Flat shift always ends after this time. |
With a pedal switch
Flat shift starts when the pedal is pressed with the throttle floored for the arming time and the engine above the minimum RPM. It ends when the pedal is released, when you lift the throttle, or after the maximum duration. A press that does not meet the conditions is ignored until the pedal is released.
Without a switch: RPM-rise detection
With the clutch released and the throttle floored, the engine speed rises much faster than it ever does in gear. On the development car, in-gear full-throttle acceleration stays under about 2700 rpm/s, while a free-revving engine reaches 7400–8000 rpm/s; the base threshold of 5000 rpm/s sits between the two.
- The arming time is what keeps a quick blip of the throttle from being taken for a shift.
- Detection is suspended while the rev limiter is cutting.
- Flat shift ends when the engine speed has dropped by 500 rpm, when you lift the throttle, or after the maximum duration.
These thresholds were set on one car and gearbox. Treat them as starting points and check them at moderate RPM first.
Rev limiter
Limiters & protections › Rev limiter holds the settings of the fuel-cut limiter:
| Setting | What it does |
|---|---|
| RPM | Where the cut starts. From here the stock limiter removes cylinders progressively. Maximum 8160 rpm. |
| Hard cut | Above this engine speed all cylinders are cut at once. Set it just above the limiter RPM for a hard limiter. |
| Hysteresis | Full fuelling resumes below the limiter RPM minus this value. |
| Step delay | Engine cycles between two cut or resume steps: lower is harder. |
| Fixed timing | Optional: while the limiter is cutting, the base ignition angle is replaced by a fixed value. |
| Live RPM | A limit you can change with the engine running. 0 = use the flashed limiter RPM. Values below 2048 rpm are ignored. |
The live limit makes it easy to lower the limiter for a test session and raise it again without flashing. Launch control, flat shift and the protections always cut hard.
Lean-AFR protection (lean cut)
Cuts the engine when the measured mixture is too lean under load. It needs a wideband that is ready.
- Margin over target: trips when measured AFR exceeds the target of the current cell by this much (0 switches this check off)…
- AFR ceiling: …or when it exceeds this absolute AFR, whatever the target (21 = no ceiling).
- Min MAP: only above this manifold pressure, so that it stays quiet at light load and on overrun. About 85 kPa covers full load on a naturally aspirated engine.
- Delay: how long the mixture must stay lean before the cut, so that the short lean spikes of a throttle stab are ignored. Cut duration: how long the cut lasts.
Boost cut
Cuts above a manifold-pressure threshold and releases once pressure has dropped by the hysteresis. Like everything related to boost, it has not been validated on a car yet.
The Protections gauge
The Protections gauge is 0 when nothing is limiting, and non-zero when launch control, flat shift or a protection is acting. Add it to your dashboard when you test these functions.


