Documentation — FAQ & troubleshooting
MS41 Live / Docs / FAQ & troubleshooting
FAQ & troubleshooting
Short answers first, then what to check when something does not behave.
Compatibility
Which ECUs and cars?
The Siemens MS41 of the BMW M52 with single VANOS, 1995–1998: E36 320i / 323i / 328i, E39 520i / 523i / 528i, Z3. Developed on a European-market ECU with a manual gearbox. Not validated yet: US-market MS41.1 ECUs and automatic gearboxes. The M52TU (double VANOS) uses a different ECU and is not supported.
Is anything modified inside the ECU?
No. MS41 Live is firmware; the sensors use pins that exist on the connector.
Can I go back to the original software?
Yes, with a full flash of the file you saved before installing, using your flashing tool. Make that backup before anything else.
Is boost supported?
The tables run to 200 kPa absolute and there is a boost cut and a lean-AFR protection. Boost has not been validated on a car yet; the base tunes’ values above atmospheric pressure are untested.
Does it work with an automatic gearbox?
Not validated. The firmware has only been run with a manual gearbox.
Can I keep the MAF, or the stock oxygen sensors?
MS41 Live runs on a MAP sensor and a wideband. The old MAF modes are no longer supported: the editor flags them and offers to switch to the VE table. Stock narrowband sensors (one or two) can still be selected on the Inputs & sensors page, but they are not recommended: the closed loop only regulates to lambda 1 and there is no lean-AFR protection. They have not been validated on a car.
Does the trip computer still show the right fuel consumption?
With different injectors it drifts. System › Instrument cluster has a correction factor: if the displayed consumption is too low, raise the factor by the same percentage.
Connection
“Live: connect” gets no answer from the ECU
- Ignition on?
- Any diagnostic or logging program still holding the cable? Close it.
- The right serial port? Unplug the cable and look at which port disappears.
- Connect with the ignition on or the engine idling rather than while driving.
The editor says the ECU is not running MS41 Live
The firmware is not installed. The first installation is a full flash with your flashing tool: see Getting started.
My browser has no “Live: connect” that works
The connection needs Web Serial: use desktop Chrome or Edge. Firefox, Safari and phone browsers do not provide it.
The connection drops after a while
Check the cable and its plug first; a loose diagnostic plug is the usual cause. Reconnect: the editor compares its values with the ECU’s and asks what to do if they differ.
Live tuning
I see the gauges but my edits are not applied
Live writing becomes active once the engine is running. With the engine stopped, edits wait. Also check that “Live tuning” is enabled on the System pages.
After switching off, my changes are gone
Live edits are in ECU RAM and are lost when the ECU powers down. Flash the partial to keep them: Flashing.
After a short stop, my live values were still there
The ECU stays powered for a short while after the ignition is switched off, so a quick restart can find the RAM values intact. To go back to what is flashed, use the “flashed values” button of the editor.
Which settings are live?
The VE, AFR target and ignition tables, the launch, flat-shift and live-limiter settings, and every other setting that carries a LIVE badge in the editor. Settings marked FLASH take effect after a flash.
Sensors
MAP does not read barometric pressure with the engine off
Check the sensor’s 5 V and ground, then the preset or the slope and offset. A reading that is wrong by a constant factor is a slope problem; one that is wrong by a constant amount is an offset or ground problem. See Sensors & calibration.
AFR is stuck at one value after a start
The wideband controller is heating its sensor. Until its output passes the not-ready threshold, the reading is not a measurement, and there is no closed loop and no lean cut.
The AFR gauge and my controller’s display disagree
Check the wideband preset against the controller’s analog-output settings (gasoline AFR), then the analog ground: it belongs on the sensor ground, not on the chassis.
The fuel trim stays at zero
Closed loop is not active: wideband not ready, engine not yet warm enough, or an operating point where the stock strategy runs open loop.
The ECU stores oxygen-sensor heater faults
Expected once the stock sensors are removed. In wideband mode they do not prevent closed loop.
Flashing
The flash stopped half-way
Keep the ignition on, do not start the engine, check the cable and press Resume flash. If that is not possible: ignition off for 10 seconds, on again, reconnect and flash the partial again. Details in Flashing.
The flash stops at the link test
The cable does not hold the fast speed. Nothing was erased. Switch the ignition off for 10 seconds and start again: the editor now uses the slower speed.
The editor refuses to flash with the engine running
Flashing is done with the engine stopped and the ignition on.
Something else? Write to contact@ms41-live.com with the car, the engine, your sensors and what you see.
