Documentation — Changelog
Changelog
Release notes for the firmware, the editor and the base tunes.
R113 Beta
Everything on MAP × RPM, a VANOS table, and a base ready for boost.
Firmware and base tunes
- The stock BMW tables (warm-up, transients, idle, knock, VANOS corrections…) are now indexed by MAP, like the VE, AFR target and ignition tables. They were refitted on real driving logs so that they behave like the stock load-based tables.
- VANOS: ON / OFF table on MAP × RPM, or the stock BMW logic. Base tunes: stock behaviour up to 100 kPa, off under boost.
- Knock detection: back to the stock MS41 thresholds.
- Boost-ready base tunes: AFR targets and ignition above 100 kPa, boost cut at 180 kPa absolute, lean-AFR cut above 110 kPa. Nothing changes below 100 kPa.
- New base tunes for M52B20, M52B25 and M52B28 (gasoline, stock injectors).
Editor
- Built-in logger: record, view, import and export logs (RomRaider format); VE correction proposed from the wideband.
- Stock BMW tables shown and edited in kPa; VANOS ON / OFF table.
- MAP sensor + wideband is the supported setup. The MAF modes are no longer supported (the editor offers to switch to the VE table). Stock narrowband sensors remain possible but are not recommended.
Known limits of this release
- R113 has not been driven yet: it has been checked in an emulator of the ECU and in the editor only.
- The full flash is needed once to move from R100 to R113 (new program).
R100 Beta
The first beta release.
Fuel and ignition
- VE-based fuelling (speed density): VE table 16 × 20 on MAP × RPM, up to 200 kPa, with intake-temperature correction.
- AFR target table 16 × 20 on MAP × RPM, used by the fuel calculation and by the closed loop.
- Ignition table 16 × 20 on MAP × RPM; stock BMW corrections and knock control kept.
- Engine and injector settings: displacement, injector flow, dead time, fuel density, stoichiometric ratio.
- MAF mode with the stock BMW maps remains selectable.
Lambda
- Wideband closed loop from a 0–5 V controller, regulating to the AFR target table.
- Stock narrowband modes (one or two sensors) selectable.
Live tuning and flashing
- Live editing of the VE, AFR target and ignition tables and of the launch, flat-shift and limiter settings, written to ECU RAM.
- Live gauges (about 6 samples per second), cursor on the active cell, full-screen dashboard.
- Partial flash from the browser (24 KB, about 25 seconds at 62 500 baud): link test before erase, block-by-block confirmation, read-back, resume, guided key-off / key-on.
- Reading the tune back from the ECU; automatic checksum correction.
Motorsport
- Launch control: RPM limit with fixed ignition.
- Flat shift: clutch switch, or clutch-less detection from the RPM rise rate.
- Hard-cut rev limiter, adjustable live; lean-AFR protection; boost cut.
Inputs and sensors
- MAP, wideband and clutch switch assignable to the Lambda 1 pin (75), the Lambda 2 pin (76) or the MAF signal pin (8).
- Presets — MAP: Bosch 3 bar, AEM 3.5 bar, GM 3 bar; wideband: AEM X-Series, Innovate, Spartan, PLX. Conflict warnings.
Base tunes and interface
- Base tunes for M52B20, M52B25 and M52B28 (gasoline, stock injectors).
- Editor in English and French.
Known limits of this release
- Developed and driven on one car: E39 523i, M52B25, manual gearbox, naturally aspirated, E85 with 660 cc injectors.
- Not validated on a car yet: boost; the three gasoline base tunes; input re-mapping; narrowband modes; automatic gearboxes; US-market MS41.1 ECUs.
- The first installation needs one full flash with an existing MS41 flashing tool.
