Documentation — Base tunes
Base tunes
MS41 Live comes with one base tune per engine: M52B20, M52B25 and M52B28, on gasoline with the stock injectors. They are starting points, meant to be trimmed with the wideband — not finished tunes.
Status. The tune that has actually been driven is the development car’s: M52B25, E85, 660 cc injectors. The gasoline / stock-injector M52B25 base tune is derived from it, and the M52B20 and M52B28 base tunes are scaled from the B25. None of the three has been run on an engine yet.
The three engines
| Engine | Displacement | Stock injector | Flow used (at 3.5 bar) |
|---|---|---|---|
| M52B20 | 1991 cc | Bosch 0 280 150 415 | ≈ 184 cc/min |
| M52B25 | 2494 cc | Bosch 0 280 150 415 | ≈ 184 cc/min |
| M52B28 | 2793 cc | Bosch 0 280 150 440 | ≈ 231 cc/min |
The injector flows come from parts listings, not from an official data sheet. They are close enough to start: the closed loop absorbs the difference, and you correct the injector flow or the VE table from what the wideband and the fuel trim show.
What a base tune contains
- VE mode: MAP sensor on the Lambda 2 input (pin 76), wideband on the Lambda 1 input (pin 75) with the AEM X-Series calibration. The MAF is not used.
- Fuel: gasoline, stoichiometric ratio 14.7, density 0.745 g/cm³. For E10, set the stoichiometric ratio to 14.1.
- VE table: the one measured on the development M52B25, used for all three engines.
- AFR targets: 14.7 at light load, richer towards full load; into boost 12.0 at 110 kPa down to 11.0 at 200 kPa.
- Ignition: a MAP × RPM table derived from the stock BMW M52B25 timing. Above 100 kPa: the 100 kPa value minus 2° per 10 kPa up to 140 kPa, then minus 1.5° per 10 kPa — conservative and untested.
- Stock BMW tables (cranking, warm-up, idle, acceleration enrichment, knock, VANOS corrections, overrun fuel cut): the stock BMW M52B25 calibration, indexed by MAP and fitted on real driving logs so they behave like the stock load-based tables. Cranking fuel is scaled for the injectors and displacement of each engine.
- Knock: the stock MS41 knock-detection thresholds.
- VANOS: an ON / OFF table on MAP × RPM — stock behaviour up to 100 kPa, off under boost.
- Protections: boost cut at 180 kPa absolute; lean-AFR cut above 110 kPa. Both stay inactive on a naturally aspirated engine.
- Launch control and flat shift off; clutch by RPM-rise detection; live tuning on.
- The base tunes do not require the EWS immobiliser signal.
Stock injectors are far too small for boost: fit bigger injectors and enter their flow before running any boost.
Stock narrowband sensors can be selected instead of a wideband, but it is not recommended: see Sensors & calibration.
What to check first
- Your hardware against the tune. Displacement, injector flow and dead time on Fuel › Engine & injectors. If your injectors are not stock, enter their data before the first start.
- The sensor calibration. MAP preset or slope / offset, wideband preset. Engine off: MAP = barometric pressure. See Sensors & calibration.
- The fuel. 14.7 for gasoline, 14.1 for E10.
- First start. Watch AFR against target as soon as the wideband is ready. If the engine is clearly rich or lean everywhere by the same amount, correct the injector flow rather than the whole VE table.
- Idle and light load, engine warm: tune the VE cells you can hold steadily. Then cruise, then progressively higher load. See the Tuning guide.
- Timing. Watch the Knock gauge. Do not assume the ignition table is right for your engine, fuel and compression.
Other fuels and injectors
The development car runs E85 on 660 cc injectors with the same firmware. For another combination, start from the base tune of your engine and enter the injector flow, the dead times, the density and the stoichiometric ratio of your fuel (E85 is around 9.8, depending on its actual ethanol content). The AFR targets stay on the gasoline scale: 14.7 is always lambda 1.
